Dillon Quantrol Torque Testing Equipment |
|
Dillon Quantrol Orbis Packaging Testing System
Measures performance characteristics of a screw closure for each stage of its life cycle. Accuracy of 0.5% of capacity with backlight, inverting display, simultaneous display mode, rechargeable batteries, PC interface, data output. Available in tamper-evident version
|
- Capacity: 0 to 6 N-m (0 to 50 in-lb) |
from $1710 |
 |
Torque Wrench Checker
A simple and reliable method of monitoring the torque applied by any click-action, break back or dial indicator torque wrench. An excellent tool to ensure the torque wrenches in your facility are accurate. 2000 Hz peak detection, pass/fail indicators, RS232, measures in N-m, kg-m, kg-cm, lb-ft and lb-in |
- Rated torque range: 15 m-N to 1000 m-N (11 ft-lb to 720 ft-lb)
- Resolution: 15 x 0.005 N-m to 1000 x 0.2 N-m (11 x 0.002 lb-ft to 720 x 0.2 lb-ft) |
from $2345 |
 |
Dillon Quantrol AFTI Advanced Torque Gauge and Torque Indicator
1/5000 resolution with 5000 Hz data acquisition, pass/fail alarms, Smart Sensor recognition, Advanced loadcell cartridges can be changed in seconds, configurable peak capture rate, auto off, data storage for up to 100 peak values, average load measurement, optional foot switch, RS232, digimatic and +/-4 VDC Analog outputs |
- Capacity: 22 to 22000 lbs (100 to 500 N and 10 to 100 kN) |
- Gauge: $820
- Advanced Loadcells: from $470 |
| Smart Torque Sensors available for AFTI |
 |
Static Torque Wrench
Fitted with a 1/2" square drive ready for standard sockets and adapters |
- Capacity: 15 Nm to 1000 Nm (11 ft-lb to 737 ft-lb) |
$1080 |
 |
Rotary Torque Sensor
Measures both rotational torque and static torque with round or square drives |
- Capacity 18 in-lb to 184 ft-lb (2 Nm to 250 Nm) |
from $1450 |
 |
Static Torque Sensor
Designed to be mounted to a bench or test fixture to measure torsional forces. Measures static torque in both directions. Standard 3/8" male square drive. |
- Capacity: 110 ft-lb to 737 ft-lb (150 Nm to 1000 Nm) |
from $1520 |
 |
Static Torque Screwdriver
Use as a handheld device or mount to a bench stand. Includes drill-like chuck for screwdriver bits and 3/8" square drive for socket attachment |
- Capacity: 3 in-lb to 88 in-lb (300 Nm to 1500 Nm) |
from $940 |
Imada Torque Testing Equipment |
 |
HTG2-Series Digital Jacobs Chuck Torque Gauges
Programmable high / low setpoints, 960 data memory, reads in lb-in, kg-cm and N-cm, RS232, digimatic or analog outputs, real time and peak mode selectable, tare, overload alarm and low battery indicator, built in rechargeable NiCad batter and AC adapter |
- 70 x 0.01 oz-in
- 15 x 0.01 lb-in
- 40 x 0.01 lb-in
- 85 x 0.1 lb-in |
$1365 |
 |
DTX2 Digital Cap Torque Tester
Programmable high / low setpoints, 960 data memory, clamps containers from 1/2" to 7" diameter, RS232, reads in lb-in, kg-cm and N-cm, digimatic or analog outputs, real time and peak mode selectable, tare, overload alarm, built in rechargeable NiCad batter and AC adapter |
- 15 x 0.01 lb-in
- 40 x 0.01 lb-in
- 85 x 0.1 lb-in |
$1635 |
 |
Imada DI-5-RL Torque Gauge
Reads in lb-in, kg-cm and N-cm, peak, real time and peak down measuring modes, 400 data memory, programmable high / low setpoints, zero reset, RS232, internal NiCad battery or AC adapter, ±0.5% F.S. ±1 LSD accuracy |
- 0.15 ~ 18 lb-in
- 1.5 ~ 90 lb-in
|
$985 |
 |
Imada DI-5N-TW20 Torque Gauge
Reads in lb-in, kg-cm and N-cm, peak, real time and peak down measuring modes, 400 data memory, programmable high / low setpoints, zero reset, RS232, internal NiCad battery or AC adapter, ±0.5% F.S. ±1 LSD accuracy
|
- 0.15 ~ 180 lb-in |
$1245 |
 |
Imada DSD-4 Torque Screwdriver / Torque Tester
Available in: lb-in, oz-in, kg-cm, N-cm or N-m, peak, real time and peak down modes, 400 data memory, programmable high / low setpoints, programmable screw tightening counter and auto zero function, CW and CCW operation, RS232, internal NiCad or AC adapter |
- 0.3-35 lb-in
- 3-560 oz-in
- 0.3-40 kg-cm
- 3-499 N-cm
- 0.03-4000 N-m |
$595 |
 |
Imada DSW-15 Torque Wrench
Available in lbf-in, oz-in, kg-cm, N-cm or N-m versions, peak, real time and peak down modes, 400 data memory, programmable high / low setpoints, programmable screw tightening counter and auto zero, CW and CCW operation, RS232, internal NiCad or AC adapter |
- 3-130 lb-in
- 30-2100 oz-in
- 3-150 kg-cm
- 100-1500 N-cm
- 1-15 N-m |
$985 |
 |
Imada DW-75 Torque Wrench
Available in lbf-in, lb-ft, kg-cm or N-m versions, wrench head swivels 300°, ±0.5% F.S. ±1 LSD accuracy, 400 data memory, CW and CCW operation, RS232, internal NiCad or AC power, programmable high / low setpoints |
- 3 - 660 lb-in
- 0.3 - 55 lb-ft
- 3 x 750 kg-cm
- 0.3 - 75 N-m |
$1245 |
 |
Imada I-Series Non-Impact Torque Testers for Power Drivers & Wrenches Imada i-series digital torque testers are ideal for calibrating power screwdrivers with torque control. With peak mode, real time mode and peak down mode. Standard 3/8 inch drive. Comes with RS-232, case, 2 adapters. |
- 0.03 ~ 7.0 lb-in (0.001 lb-in)
- 0.3 - 70.0 lb-in (0.01 lb-in)
- 1.5 - 130.0 lb-in (0.1 lb-in) |
from $1390 |
 |
DI-3N-Digital Torque Testers with Remote Sensors
Imada DI-3N-IP digital torque testers with a flanged remote sensor calibrates torque tools up to 362 lb-ft with accuracy of +/- 5% FS. Measures in peak, real time and peak down modes. 400 internal memory and RS-232. In lb-in, kg-cm, N-cm or lb-ft, kg-m and N-m |
- 0.30 - 44.0 lb-in
- 3.0 - 440.0 lb-in
- 30.0 - 1800 lb-in
- 3.0 - 145.0 lb-ft
- 3.0 - 362.0 lb-ft |
from $1295 |
 |
Imada DI-1M Digital Torque Tester for Air Tools & Impact Torque Wrenches
Imada DI-1M torque testers are perfectly suited for on-the-spot calibration of impact drivers and air tools, but will calibrate any type of power driver. With peak, real time and peak down modes. With RS-232 and accuracy of +/-0.5%. Measures in lb-in, lb-ft, kg-cm, kg-m, N-cm or N-m. |
- 3.0 - 440.0 lb-in
- 30.0 - 1800 lb-in
- 3.0 - 145.0 lb-ft
- 3.0 - 362.0 lb-ft |
$1980 |
 |
Imada DI-4B-25 Air Tool & Impact Wrench Digital Torque Tester
Imada DI-4B-25 fast response torque testers are perfectly suited for on-the-spot calibration of air tools and impact drivers, but will calibrate any type of manual wrenches. With peak, real time and peak down modes, RS-232 and accuracy of +/-0.5%. Measures in lb-in, kg-cm and N-cm |
- 3.0~220.0 lb-in |
$1685 |
Chatillon Torque Testing Equipment |
 |
Chatillon DFS-R-ND Series with Remote Loadcell
Accurate load and torque measurement with the same gauge. Accuracy >= 0.25% full scale with interchangeable sensors and >= 0.1% full scale with a dedicated SCL load sensor. With normal and peak readings, high / low limits, setpoints, pass / fail results, statistical results, load averaging, load comparisons, percentage and sharp break detection, sensor actuation and direction. Measurements are displayed in ounce, gram, pound, kilogram or Newton units or in oz-in, g-cm, lb-in, N-cm and N-m units. Results displayed in oz, g, lb, kg or N units or in oz-in, g-cm, lb-in, N-cm and N-m. With RS232 |
Torque:
- 3 lb x 0.0005 lb
- 12 lb x 0.002 lb
- 50 lb x 0.01 lb
- 100 lb x 0.02 lb
- 200 lb x 0.04 lb
Load:
- 0.55 lb x 0.0001 lb
- 2.2 lb x 0.0005 lb
- 11 lb x 0.002 lb
- 22 lb x 0.005 lb
- 50 lb x 0.01 lb
- 100 lb x 0.02 lb
- 220 lb x 0.05 lb
- 560 lb x 0.1 lb
- 1100 lb x 0.2 lb |
Gauge $860
Torque Sensors $935
Load Sensors from $430
|
 |
Mark 10 BGI Universal Digital Force / Torque Gauge
Interchangeable remote torque and force sensors. Mitutoyo, RS-232, and analog outputs. Test up to 5,000 lb/in of torque and 10,000 lb of force. Full computer control capabilities
|
- Capacity: 0.25 to 10000 lbs |
Gauge: $821
Sensors from $565 |
|
Mark 10 MGT Digital Torque Gauges
±0.5% accuracy. Dedicated remote torque sensor with Jacobs chuck and compact size. Rugged aluminum housing with peak memory for clockwise and counterclockwise readings. With push button calibration and 30 readings/second sampling rate.
|
- Capacity: 10 oz-in to 100 lb-in |
from $1026 |
|
Mark 10 CT Closure Tester
±0.5% accuracy. A powerful, yet value priced solution for closure manufacturers, bottlers, food and beverage companies, and others. Broad sample size range, rugged construction and simple hand operation.
|
- Capacity: 12 to 100 lb-in |
$1325 |
 |
Mark 10 TST / TSTH Manual Torque Test Stands
Ideal for a wide variety of torque testing applications up to 100 lb-in, including closure torque testing, fastener torque testing, and more. The TST’s versatile modular design allows it to be configured for a variety of torque sensors and gripping fixtures.
|
- Capacity: 100 lb-in |
$2470 |
 |
Mark 10 ST Torque Tool Tester
A simple yet accurate solution for testing torque screwdrivers, wrenches, and other tools. Applications exist in manufacturing facilities in virtually every industry. The ST features a solid aluminum housing, making it rugged enough for many years of service in production or laboratory use, while a universal receptacle with square drive and grooves accepts common bits and attachments.
|
- 12 x 0.01 lbin
- 50 x 0.05 lbin
- 100 x 0.1 lbin |
$1135 |
